What you will want to find is a electronic flasher that is rated for LEDs available at most autopart stores. Like the tridon ep37. It will have 2 terminals marked X and L the X will connect to your 12v+ and the L will connect to the center of your three position switch. Your left and right lights will come off the other 2 terminals. This flasher will flash at the same rate no matter what the load is.

 

Thanks Jimmy!! And if I wanted to make hazard lights work, could I come off of the same flasher with a SPST switch to all LEDS?

As far as ground wires, do you think it's better to loop all grounds together to a single good ground point? Thanks again.

 

I individually grounded each light on my UTVINC LED Turn Signal Kit...

 

Thanks Swing arm. Yeah that would seem to be better for trouble shooting a bad lamp down the road. I was going to use trailer lamp wire and it has a ground built in, so figure I would just take to the same spot.

 

Thanks Swing arm. Yeah that would seem to be better for trouble shooting a bad lamp down the road. I was going to use trailer lamp wire and it has a ground built in, so figure I would just take to the same spot.

I agree...

 

You would actually have to use a double pole single throw for you hazard flashers. Because you would have a electrical connection between your left and right if you used a single pole. And when you went to use your turn signal the left and right would flash.you would feed both poles of the switch with the same 12v as your turn signal on the load side of the flasher and then to the left and right off of the separate pole of the switch. Hope this helps. Jim

 

Thanks again Jim, I was just testing you. Hahaha
Henry

 

What size fuse should I use for each side? Have 2 LED on front left and 2 on front right with 1 one left and right rear. So total of three for each flash.

 

Jim

I am really lost when it comes to electric but here is my question. I want to put turn signals on my 2011 and think that having hazards would be a good thing to have as well. I don't know which to go with weather to use led or regular bulb type? Also I would like to had a backup light and front additional light. Which would you suggest for this? Hids or Leds, I question the battery and the starter to handle this. I appreciate your time with this in advance. Oh yea where would you suggest to get some of these things.

Matt

 

I apologize for not replying sooner I been out of town deer hunting. If you have any problems with your install just let me know. I'm always glad to help. I live in central Ohio also so I could give you a hand if you don't feel comfortable with something. As for your question I prefer led over incandescent . I bought 4 inch round 18 watt led lights off eBay and have 2 of them installed for back up lights( major overkill )and 2 facing forward in addition to HIDs in my stock headlights. Jim
http://s304.beta.photobucket.com/us...3CD7C3FD-4EB5-493A-A477-063785F855BC-13557-00000C5D233498F9.jpg.html?sort=3&o=0

http://s304.beta.photobucket.com/us...E79DD3C6-9B20-4E06-83BE-7797A6B8B218-13557-00000C5CF6B345DC.jpg.html?sort=3&o=1

 

Matt, I got all mine off of eBay and saved $$$.

Henry

 

by any chance do you have the part list or who you got the parts from. Having a little trouble finding a small enough lenses as the turn signal. I am thinking of drilling my rear brake lights to add the turn signals. On the front I was thinking of using something small. What did you use. Do you have any pictures?

 

Suggo,

Here is the ebay link to where I got the LED's:
Maxxima 3/4" Side Marker Combination Clearance light LED Red Clear Lens | eBay

Here is the horn button I used:
WATERPROOF YELLOW PUSH BUTTON 12V MOMENTARY SWITCH AUTO / BOAT / MOTORCYCLE | eBay

Here is the flasher I used:
EF32SS Solid State Flasher, LED Compatible 2 Prong | eBay

I used two amber LED's on each front side and one red LED in each break light.

I used these little guys for dash indicators:
LED GREEN LIGHT - CHROME METAL CASE - 12 VOLT - DASH INDICATOR - SWITCH USE | eBay

These are the license plate lights I used:
2x White LED SMD Motorcycle & Car License Plate Stud Screw Bolt Light lamp bulb | eBay

I will post some pics of my install tomorrow morning. Let me know if you have any other questions.

Henry

 

Signals and switch/stalk I used from ebay as well.

Front Signals - Flush GSXR LED $15 (ebay):

Turnsignal/Hazard/Horn Switch - VSM 920 Universal $21 (ebay):

Rear signals - (OEM brake lights):

 

Henry,

Thanks! I am going to get on this, this weekend. I have been told that Ohio is not every going to allow RZR's to be street legal, so I am just goint to do everything that they require for a golf cart and just mind my manners when I am in the neighborhood. This is going to help a lot. Thanks again.

 

Sorry took so long. Here are pictures of my install.

Front turn LED

License plate install with LED bolts:

Turn switch location:

Horn button:

Turn Indicator LED:

 

Nice job, looks great

 

Jim

No big deal, hope you got one from the stand. I am still getting all the parts together to do it. I am hoping to be able to get to it after the holidays and things tend to slow down a bit. Thanks again for all your help and will be in touch for sure.

 

I looked on Ebay for your VSM 920 switch. Can you give an item number or path to the website?
Thanks