Polaris RZR Forum - RZR Forums.net banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 20 Results
  1. RZR 800 Specific Discussion
    My prop drive shaft broke today while out riding what is the best replacement ?? Weld this one back together or is there a place that makes stronger ones?? Thanks
  2. General RZR Discussion
    Has anybody installed a armrest in there rzr? Or know if they make one for the rzr? Ive thought about trying go to a junkyard and fine a ford focus armrest or something and try that. It just seems like dead space in between the seats.
  3. General RZR Discussion
    Will the Nuvi 500 operate and charge using a USB port connection while connected to the RZR? If so I would rather do that than run a bulky 12 volt plug-in.:popcorn:
  4. General RZR Discussion
    I figure how hard can it be to find an OK looking lid that would fit a 6" can so I stop at a Salvation Army on my way home. They had about a dozen lids on the shelf and about that many small covered pots. I bought 2 lids that looked promising. I didn't find any that would fit tight over a 6"...
  5. Lighting, Stereo and Electrical
    please post info. and pic.
  6. Polaris RZR Parts & Accessories Classifieds
    Effective April 1st, 2013 the new price for the harness will be $100 including shipping. I have absorbed several price increases in my materials (especially the copper wire) and shipping over the past 40 months. A recent bump in shipping costs was the last straw. I will honor any past quotes...
  7. General RZR Discussion
    So who plows snow? (Yes, I know it's august!) I've got a 2002 Magnum 325 that I've plowed with for years, it's getting sold as soon as I fix a couple little issues on it so now I have to decide whether to get a plow for the RZR or a nice snow blower. How are the Polaris plows? Easy...
  8. General RZR Discussion
    This is my attempt to mount a Donaldson filter on a stock Rzr and connect it to the stock air intake. No snorkels, no hole in the panel behind the seat. It's as 'factory' looking as I could make it. Hopefully it'll perform WAAAYYY better than factory! After over 1 1/2 years of research I've...
  9. General RZR Discussion
    Simple question: If you've removed the clutch spacer did it cause any problems with your drivetrain?
  10. Suspension
    Here's some measurements I made on the stock Rzr shocks: FRONT Polaris No: 814902001182 Mfr: Sachs/Mexico Length eye-to-eye: 16.25" Bushing: 13/32 (10mm) ID, 5/8 OD, 1 3/16 long Spring preload (lowest setting): 220 Lbs. Spring Rate: 100 Lbs per Inch Spring Free Length: 12.375", 6.5 free...
  11. General RZR Discussion
    After you've gotten a mount you can install the winch in the Rzr. This one was made by member Martymoe and features a clever fairlead extension that clears the chassis and lowers the fairlead in the opening of the Rzr nose. There already is a factory location for the winch electrical...
  12. General RZR Discussion
    It seems to me that the air intakes offered by BTI and DFR both address the Polaris engineering mishap. So the questions becomes how should a person choose between the two? Jason
  13. Projects and How-To
    Just thought I would throw my 2 cents in. Installed a simple drain in the clutch cover. Got the idea from the site & tried it. It was a simple install. I bought the shortest valve stems that I could find. Cost about $3.00. They came with the rounded ends that you can see in pic 1. I ground...
  14. Projects and How-To
    3/2012 edit: Have a look here and at this thread for the specific changes required for the 2011-12 Rzr. 7/2011 edit: Found out black ABS parts can be ordered from any ACE hardware store. Free delivery to your local store...cheap & easy! I've been on the fence for many months trying to...
  15. Projects and How-To
    I finally got around to fabbing up a parking brake for the RZR. It took me some time to figure out how I was going to incorporate a cable pull system attached to the brake peddle without having to weld anything because I wanted to make it as simple as possible. The biggest hurdle was figuring...
  16. General RZR Discussion
    Has anyone found an aftermarket E-brake for the RZR? I am so used to parking my fourwheeler anywhere. I keep getting stuck in Park parking my RZR on hills. It's driving me nuts. I'm thinking of building my own.
  17. Engine and Drivetrain
    Ok guys well some of you may remember all the problems I had with the Dragon Fire canister. After reading a post by Megadesert about the UMP canister I thought what the heck I'll try one since I have had two different Dragon Fire Racing canisters, the first one broke and the 2nd had a different...
  18. Projects and How-To
    I did some experimenting with mounting 4-point restraints and this is what I learned: The type I chose uses a push-button latch. This is a matter of personal preference. I've used racing latches in the past and I was always the last guy in a group to leave due to fumbling with the...
  19. Projects and How-To
    No way I'm paying $18 each for the L&R hold-downs. They can only clamp something down to the bed and don't provide a place to tie off or anchor a bungee. So I made my own. There are a few different types of expanding rubber plugs available in hardware, boating and plumbing stores. Here are...
1-19 of 20 Results
Top