What is ur ground clearance

Just wondering what kind of ground clearance u have mine is 14.5"

__________________
Dothan, Alabama

2008 rzr racer tech engine mount, 28" zillas, 14" rims, 2" lift, warn 30, epi trail and mud clutch, s fender flares, Maier Vented Hood and optima battery, home made stereo

What lift do you have? How and where are you taking your measurement? I have the 3" roktek lift with highlifter springs fully adjusted and after compressing my shocks and letting the rzr rebound on its own, my ground clearance is 12" . I'm taking the measurement at the lowest point which is at the front middle bolt of the belly skid plate.

__________________
J & T

I have rubberdown lift and stock springs on the second click with 900 miles and i am at about 13 1/4"

__________________
Gen 3 RZR , Rubberdown 2" Lift
12x7 KMC Enduro Beadlocks , 26x11x12 Mudlites
2" Wheel Spacers , EMP Grille
Dirty Dawg Performance Clutch Kit w/o spacer
Looney Tuned Dual Exhaust
KMS Performance Billet Intake
Snorkeled and Sealed Everywhere
Removed Front Sway Bar , HPD Steering Bearing Kit

2'' lift, hl springs, 13 at the bottom of skid in the rear, had same with stock springs. 26'' tires.

Well heck I seem to have the smallest ground clearance than all you guys (I'm running 26" bighornes), so I can relate to Deez Nutz avatar but Im happy where I'm at and wont no part of the devil.

__________________
J & T

Ive read the roktek 3'' does not give the true 3'' lift, but am more interested in any updates from you guys running this lift? If you jack the rzr rear tires off the ground can you still rotate the wheels easily or does it bind the cvs. Ive found with standard 2'' lifts it lets the suspension drop to dangerous angles that if your rear wheel drops can break a axle or cv. This kit says it limits over travel to safe limits. Would really like someone with one to check and let us know if thats true. Im looking for the safe drop more so than more lift than 1.5-2''.

I measured at the rear hitch and on the side. 2" lift with 28" zillas

__________________
Dothan, Alabama

2008 rzr racer tech engine mount, 28" zillas, 14" rims, 2" lift, warn 30, epi trail and mud clutch, s fender flares, Maier Vented Hood and optima battery, home made stereo

I have the same lift with 25" tires. 12" at bottom of hitch receiver with the pre loads set on the lowest setting.

OK, If we all don't measure the same, then none of our answers mean anything. So I vote for everybody that is interested in ground clearance to decide where and how (lifting it up on a jack and letting the rzr down easy to where it rests, preloading the shocks and letting the rzr rebound on its own, or just lifting it up with all your might for those awesome looking pictures) to measure including before and after. AND WHERE!!!!

__________________
J & T

and also... Just letting it rebound on its own is not accurate either... you can measure it this way and then go out and ride the bike around and remeasure and USUALLY the measurement is less after riding. This gives the suspension to settle back in to a TRUE measurement.

Seems this thread died of .....lack of interest,NO..........lack of metric conversion tables,NO .......nobody could deliver the punchline - "Yeah, deep too!"

I truely measure ground clearance by those who that can follow me and those that can not...........

__________________
J & T

Somewhere around 22-24"....

__________________
Just Muddin!

I have an 09 Razor with less than 5 hours on it. Last weekend I put a Roktek lift on. I still have the stock springs (hope to change soon) and with the shock's turned all the way up, I am at 12-3/4" (front) and 14-1/2" (rear). Up front I measured the skidplate to the ground and in the rear I measured from the hitch to the ground.

I have rode it about 10 miles since the lift, but thats it. When I installed the lift, I rotated the tires at full droop and had no issues at all. The lift was fairly easy to install. Especially like the quick disconnect front swaybars.

__________________
Schwanny

"Keep it rubber side down, in between the ditches!"

Thank god everyone doesn't do that, because I would call you a lowrider if you tried to follow me. LoL

__________________
Just Muddin!