Polaris RZR Forum - RZR Forums.net banner

Artic Thunder Snorkel Install 2011 RZR

7K views 19 replies 8 participants last post by  Redfish 
#1 · (Edited)
I finally got my artic thunder kustoms snorkel kit installed on my rzr and I am very happy with the final outcome. I thought I would put up a few pics to show people how it turned out. I didnt take near enough pics but I have to say the install was very simple with only a few modifications other then what the instructions had given.

The only issue I ran into was with getting the lower snorkels to tuck into the groove in the underside of the box to get it to fit snug down onto the rear frame of the rzr. on my 2011 if its any different then the other years there are some flimsy little plastic ribs that narrow the channel where the lower snorkels sit up into. All I had to do was cut those off to widen the area where the lower snorkels are placed into and the rest of the install was a breeze. The instructions he gives you are fairly good and he will give you a list on the first page of what exact tools you will need to install the snorkel kit.

I ran into one other small issue that the fuel pump breather tube is actually a larger diameter then my diffs, trans and trans case breather tubes. the tubing he supplies you with works excellent for all other breathers but this one. All I did for that was grab some teflon tape and run it around the coupler that allows you to extend your vent lines until it was a snug fit.

At this time I was thinking of how I can assure everything else is sealed up as good as possible so I took apart all of my electrical connections and di-electric greased the connnections as well as took my clutch cover off and threw some marine grease around the seal to help out with getting a water tight seal. I also used marine grease on the snorkel o-ring off the air intake during modification of the riser and o-ring on the air filter cover. Took her out into some deep mud and dusty conditions and it seemed to work pretty good! I took the air filter cover off after the day of riding and the filter looked just as it did before I went riding.

Having a second person helping you with the install is a benefit too. I hope this helps out anyone a little more if they decide to install this kit as well as the other posts that people have on the artic thunder kit install.

I will add some comments that people have inputed below in response to this install. There is a vent line running from your Valve cover to the airbox. There is a slit in there from factory that will allow water to seep into the air box and possibly the engine. Sealing that up or changing out the hose entirely will ensure no water enters into somewhere it might cost a lot. Remember to seal the back of your clutch housing cover as water will weep in there and cause your belt to slip. If your planning on going really deep remember to snorkel the rad overflow tube as well. "If youre gonna run deep, I would put a barb fitting in rad overflow cap and snork it. When rad cools quick hitting deep water it makes a suction on the vent hole in the overflow and voila.... you will eat a water pump seal from dirt in system".


Anyone else feel free to add to what I have said and throw something at me if there is anything I may have done that is not quite on the money too!

Cheers. Cam. :pint:
 

Attachments

See less See more
2
#3 ·
Ahh right on I wasnt sure if this was a new or old design with the box but that clears that up.
 
#6 ·
YES, Definitely seal the back of the belt box. Learnt this the hard way going through a deep section of a river. :rm_thumbdown:
 
#7 ·
Thanks for the tip! I will add that as well when I get a chance.
 
#11 ·
#16 ·
I have had this on my 2010 S for a year and it runs fine....problem i had and somewhat still have is when you use this kit with the UTV Inc filter canister they do not leave room enough for you to get it all crammed together and it pulls on the throttle cable as well. The middle pipe hits the canister.
 
#19 ·
Just the fact that I would have swamped my machine already unless I ran the centre kit to the top. Other than that since it was a pre made kit and my buddy already had one and liked it.
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top